一：卸下硬盘的原板换上专用电路板
二：运行U6DLE 写入专用模块
三：运行U6DLE /C1 /T , CTRL+Z进入指令模式,输入启动指令然后

T>CTRL+T
会出现如下信息：
Pick current = 0000 DAC bits.

DAC offset = 0048 DAC bits.
Out In
CYL = 045E Bias = 0090 Bias = 0090
CYL = 0C5E Bias = 0046 Bias = 003D
CYL = 145E Bias = 003F Bias = 0035
CYL = 1C5E Bias = 0036 Bias = 002E
CYL = 245E Bias = 0030 Bias = 0042
CYL = 2C5E Bias = 002D Bias = 0023
CYL = 345E Bias = 0042 Bias = 0033
CYL = 3C5E Bias = 001C Bias = 0022
CYL = 445E Bias = -000C Bias = -0014
CYL = 4C5E Bias = 001F Bias = 0013
CYL = 545E Bias = 0016 Bias = 000C
CYL = 5C5E Bias = 000F Bias = 0006
CYL = 645E Bias = 000E Bias = 0004
CYL = 6C5E Bias = 000A Bias = 0000
CYL = 745E Bias = 0007 Bias = -0002
CYL = 7C5E Bias = 0002 Bias = -0007
CYL = 845E Bias = 0000 Bias = -000C
CYL = 8C5E Bias = -0006 Bias = -0010
CYL = 945E Bias = -000A Bias = -0014
CYL = 9C5E Bias = -000F Bias = -0017
CYL = A45E Bias = -0016 Bias = -001E
CYL = AC5E Bias = -0019 Bias = -0023
CYL = B45E Bias = -001F Bias = -0027
CYL = BC5E Bias = -0023 Bias = -002C
CYL = C45E Bias = -0026 Bias = -002F
CYL = CC5E Bias = -0028 Bias = -0032
CYL = D45E Bias = -002E Bias = -003A
CYL = D758 Bias = -004C Bias = -004A
Goodcopy=03
KEY 01h Valid

Ref 0125 - Hd Msk 0A00 - Hd Msk 0900 - Switch to full int.
Ready

Ref 0148 - Hd Msk 0A00 - Hd Msk 0900 - Switch to full int.
Ready

Ref 017F - Hd Msk 0A00 - Hd Msk 0900 - Switch to full int.
Ready

Ref 0146 - Hd Msk 0A00 - Hd Msk 0900 - Switch to full int.
Ready

Ref 017A - Hd Msk 0A00 - Hd Msk 0900 - Switch to full int.
Ready

Ref 0140 - Hd Msk 0A00 - Hd Msk 0900 - Switch to full int.
Ready

Ref 0117 - Hd Msk 0A00 - Hd Msk 0900 - Switch to full int.
Ready

Ref 0196 - Hd Msk 0A00 - Hd Msk 0900 - Switch to full int.
Ready
Total kicks=0008
Avg kicks=0001
OkEnd Test 04
Begin Test 07
HEAD 1x WEIGHTS 2x WEIGHTS
00 08 07 -00 -00
01 0F 0E -01 02
The AFC 1x sum of squares weight limit is HEX 2400
The AFC 2x sum of squares weight limit is HEX 1388
OkEnd Test 07
Begin Test 0C
Head00 1000
6000
等等....
四：10多个小时后会出现如下信息并且硬盘电机不再转动
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
Pgm=3F Trk=D92F(D92F).0.009 Zn=D Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ntrdy
五：然后给硬盘断电卸下专用板换回原板
进入指令模式
再次启动指令
当出现以下提示时
Log 39 - Health 0000 - Time = 02:00:36 - Sns = 00000000
Log 34 - Health 0000 - Time = 00:00:12 - Sns = 00000000
Log 31 - Health 0000 - Time = 00:28:00 - Sns = 00000000
Log 35 - Health 0000 - Time = 00:00:12 - Sns = 00000000
Log 3C - Health 0000 - Time = 00:00:02 - Sns = 00000000
Log 37 - Health 0000 - Time = 00:00:10 - Sns = 00000000
Log 3E - Health 0000 - Time = 00:00:02 - Sns = 00000000
Log 22 - Health 0000 - Time = 00:00:00 - Sns = 00000000
Log 21 - Health 0000 - Time = 00:00:18 - Sns = 00000000
Log 14 - Health 0000 - Time = 00:00:40 - Sns = 00000000
Log 26 - Health 0000 - Time = 00:06:24 - Sns = 00000000
Log 27 - Health 0000 - Time = 00:13:48 - Sns = 00000000
Log 25 - Health 0000 - Time = 00:01:38 - Sns = 00000000
Log 40 - Health 0000 - Time = 00:00:02 - Sns = 00000000
Log 4A - Health 0000 - Time = 00:04:14 - Sns = 00000000
Log 42 - Health 0000 - Time = 00:35:14 - Sns = 00000000
Log 43 - Health 0000 - Time = 00:00:18 - Sns = 00000000
Log 49 - Health 0000 - Time = 00:00:00 - Sns = 00000000
Log 48 - Health 0000 - Time = 00:08:54 - Sns = 00000000
Log 4C - Health 0000 - Time = 00:14:02 - Sns = 00000000
Total Time = 11:11:52
OkEnd Test 50

T>
好了!恭喜你成功了